FIELD CARD · TUBULAR REFERENCE DATA

DRIFT, TORQUE & COUPLING DIMENSIONS

Detailed procedures can be found on our care and handling page.

Care & Handling
01

Drift Dimensions

API Bare PipeWFES Thermoplastic Lined Pipe — Drift
Pipe Size
OD
Weight
(T&C)
Wall
Thickness
Drift
Diameter
Polycore™Modified Polycore™COTube™Enertube™Ultratube™Extreme­tube™
Tubing
(EUE)
1.9002.90.1451.5161.2501.184Well
Specific
1.1841.2501.250
2 3/84.70.1901.9011.6001.5161.5161.6001.600
2 7/86.50.2172.3472.0001.9011.9012.0002.000
3 1/29.30.2542.8672.5002.3472.3472.5002.500
4 1/212.75.2713.8333.4003.2153.3503.4003.400
Casing4 1/211.60.2503.8753.4003.2153.3503.4003.400
13.50.2903.7953.3503.1653.3003.3503.350
515.00.2964.2833.7853.5403.6853.7853.785
18.00.3624.1513.6603.4303.5603.6603.660
5 1/215.50.2754.8254.3004.0504.2004.3004.300
17.00.3044.7674.3004.0504.2004.3004.300
20.00.3614.6534.2003.9274.0504.2004.200
23.00.4154.5453.9503.8003.8503.9503.950
723.00.3176.2415.6005.3005.5005.6005.600
26.00.3626.1515.5005.2005.4005.5005.500
29.00.4086.0595.4005.1005.3005.4005.400
02

API Torque

foot-pounds
ThreadPipe SizeWeight
lb/ft
J-55L-80P-110
MinOptMinOptMinOpt
EUE 10rd1.900" Tbg2.906608809001,190NANA
EUE 8rd2 3/8" Tbg4.709701,2901,3201,7601,7852,380
2 7/8" Tbg6.501,2401,6501,6902,2502,2803,040
3 1/2" Tbg9.301,7102,2802,2703,0303,1704,230
4 1/2" Tbg12.752,1502,8602,9603,940NANA
NUE 10rd1.900" Tbg2.75310410420560NANA
2 3/8" Tbg4.605507307409901,0101,340
2 7/8" Tbg6.407901,0501,0701,4301,4601,940
3 1/2" Tbg9.201,1101,4801,5202,0302,0602,740
NUE 8rd4 1/2" Tbg12.601,3101,7401,8002,400NANA
LTC4 1/2" Csg11.601,2201,6201,6702,2302,2703,020
13.50NANA2,0302,7102,7503,660
5" Csg15.001,6702,2302,3103,0803,1304,170
18.00NANA2,9603,9303,9805,310
5 1/2" Csg15.501,6302,170NANANANA
17.001,8502,4702,5603,4103,4704,620
20.00NANA3,1504,2004,2705,690
23.00NANA3,7004,9305,0106,680
7" Csg23.002,3503,1303,2704,350NANA
26.002,7603,6703,8405,1105,2006,930
29.00NANA4,4005,8705,9807,970
BTC4 1/2" Csg11.60Position Make-UpAs per API 5C1: “makeup torque values should be determined by carefully noting the torque required to make up each of several connections to the base of the triangle; then using the torque value thus established, make up the balance of the pipe of that particular weight and grade in the string.”
5" Csg15.00
18.00
5 1/2" Csg15.50
17.00
20.00
23.00
7" Csg23.00
26.00
29.00
API Minimum Torque Recommended; Do Not Exceed Optimum Torque
03

Coupling Outside Diameter

inches · API 5CT
ThreadPipe SizeRegularSpecial Clearance
9th Ed.11th Ed.9th Ed.11th Ed.
EUE 10rd1.900" Tbg2.500NA
EUE 8rd2 3/8" Tbg3.0632.910
2 7/8" Tbg3.6683.460
3 1/2" Tbg4.5004.180
4 1/2" Tbg5.5635.094NA
NUE 10rd1.900" Tbg2.200NA
2 3/8" Tbg2.875NA
2 7/8" Tbg3.500NA
3 1/2" Tbg4.250NA
NUE 8rd4 1/2" Tbg5.200NA
LTC4 1/2" Csg5.0005.250NA
5" Csg5.5635.800NA
5 1/2" Csg6.0506.300NA
7" Csg7.875NA
BTC4 1/2" Csg5.0005.2504.875
5" Csg5.5635.8005.375
5 1/2" Csg6.0506.3005.875
7" Csg7.8757.375

API 5CT does not specify outside diameters for special clearance couplings in sizes marked NA; however, there are industry-accepted custom dimensions used outside of API.

04

Sucker Rod Box OD

Rod SizeRegularSlimhole
5/8"1.5001.250
3/4"1.6251.500
7/8"1.81251.625
1"2.18752.000
1 1/8"2.3752.250
05

Insert Pump

Insert BoreBarrel OD
(Thin Wall)
Hold Down
No-Go Seat
1 1/4"1.5001.562
1 1/2"1.7501.875
2"2.2502.344
06

Installation Procedures

01

WFES Thermoplastic Liners — Warm Weather Handling

Above 41°F (5°C)
  • Minimum API Torque
  • Pin protectors must stay on pipe until ready to stab
  • Use of stabbing guides is recommended for all liner materials. Stabbing guides are required when installing Enertube™, Ultratube™, and Extremetube™
  • No rod guides, stabilizers, scrapers used in any portion of the string that has thermoplastic liners
  • Make sure all intrusive tools and/or equipment are free of sharp edges
  • Please keep in mind that the liner is a plastic and can be cut and/or shaved resulting in mechanical damage
  • Trucking: strip and strap every layer with 3 boards vertically aligned and straps located at boards
02

Cold Weather Handling for Enertube™ and Ultratube™ — in addition to the above

Below 41°F (5°C)
  • Special care to prevent shock or impact loads against other pipe, rigs, racks, forks, etc.
  • Do not drop pipe or allow to free fall
  • Pin protectors must stay on pipe until ready to stab
  • Use of a stabbing guide is required
  • Trucking: strip and strap every layer with 7 boards vertically aligned and straps located at boards
  • Do not drag pipe across racks or pipe
  • When available, recommend using a pipe wrangler
03

Pulling and Re-run Procedures

  • Pulling pipe: install pin protectors before standing back on rig floor
  • Re-install following above procedures
04

Miscellaneous Items

  • Reach out to a WFES representative to discuss best practices for hot oiling or hot watering for your specific service
  • Exceeding the temperature limitations for a given environment of the thermoplastic liner can cause permanent damage to the liner
  • Call your representative before hydrostatic testing and/or swabbing to help mitigate damages
07

Thermoplastic Liner Maximum Temperature Limits*

Polycore™
160°F71°CProduction
180°F82°CWater
Modified Polycore™
160°F71°CProduction
180°F82°CWater
COTube™
165°F74°CIn all services
Enertube™
210°F99°CIn all services
Ultratube™
350°F177°CIn all services
Extremetube™
500°F260°CIn all services

*Temperature limitations are dependent on well environment conditions and variables. Please contact WFES for more information.