Built to Stop Holes in Tubing (HIT)

Superior Downhole Performance

Protect your pipe, improve ROI, and keep valuable steel in service longer. WF Liners helps operators reduce corrosion, rod wear, fluid friction, workover frequency, and repeat failure cycles with thermoplastic liner systems designed for production, injection, disposal, and severe-service environments.

In suitable downhole applications, Western Falcon liners offer a proven alternative to IPC, GRE, and premature full-string replacement. With incredible field reliability, used-pipe lining, inspection support, and field-ready installation services, WFES helps operators extend run life, lower intervention costs, and recover greater value from every string.

New Thermoplastic Lined Pipe (TPL)

When paired with quality steel, thermoplastic lined pipe changes how operators approach longevity in the field. WFES supports new lined tubing packages for wells where corrosion, fluid friction, rod wear, high-volume movement, or severe-service conditions justify protection from the first run.

For continuous production cycles measured in years rather than months, new lined pipe gives operators a proven path to move downhole liquids and gases with greater reliability, smoother flow, and longer asset life.

For use in: New Drills, High-Volume Production, Completion, Severe Service Environments, Deep (10,000ft+) Disposal Wells

Lining Used Pipe

When existing tubing still has recoverable steel value, WFES lining helps operators extend asset life rather than defaulting to replacement and disposal. Used pipe can be inspected, requalified, and lined where applicable (including tubing with existing or damaged IPC) without requiring thermal burnout or liner drilling.

With no recorded holes in lined tubing joints throughout WFES injection or disposal service history, this pathway helps preserve usable pipe, lower replacement costs, and support lifecycle-focused decisions in wells where the economics of new tubing may not be warranted.

For use in: Injection Wells, Disposal Wells, Late-Life Conversions, ESP-to-Rod-Lift Conversions, Workover Programs, Asset Recovery Programs

Show us your worst well.
We won’t just find you a solution — we’ll engineer one.

// Preventing corrosion, rod wear, fluid friction, & HIT failures

Thermoplastic Liner Technology
for Longer Tubing Life

01Recover More Pipe Across More Pulls

WFES lined pipe is designed to preserve the value of the steel asset, not just protect it during a single run. While IPC programs can result in high reject rates when tubing is pulled, 80%–90% of WF-lined pipe can often be visually recertified and re-run downhole. Where applicable, WFES can also line over existing or damaged IPC without thermal burnout or drillout, helping operators reduce replacement costs, avoid unnecessary scrap and carbon emissions, and improve lifecycle ROI.

Hole-in-tubing failures are among the most expensive recurring failure modes across corrosive wells. WFES thermoplastic liners provide a chemically inert wear barrier inside the tubing string, helping prevent the localized failures that drive repetitive workovers. Since 1992, Western Falcon has recorded zero holes in lined tubing joints in injection or disposal environments.

Despite a marginal decrease in ID, lined pipe improves fluid flow through OCTG. Compared to bare steel, the smooth internal surface of thermoplastic liners helps reduce friction, pressure drop, and fluid turbulence. In applicable wells, this can support higher fluid throughput, reduced pumping demand, smaller pump requirements, lower electrical costs, fewer corrosion inhibitors, and improved operating efficiency.

WFES thermoplastic liners are flexible, ductile (moving with the rod), and built for the realities of field handling. Unlike brittle thermoset coatings or GRE systems that can be vulnerable to impact, cracking, or wireline damage, lined tubing supports unrestricted wireline speeds and aggressive wellbore interventions. In most applications, no specialized tools or procedures beyond API minimums are required for successful installation.

// Exponentially extended asset life

Built Around Well
Failure Modes

With WF Liners, there is no need for corrosion barrier rings (CBR), inserts, special torque make-up requirements, or specialized service technicians. Following standard API considerations for connections and installation will yield a highly flexible, durable, and chemically resistant solution compared to IPC, GRE, or alternative chemical treatments.

The table below compares common bare steel tubing limitations with the performance advantages that WFES thermoplastic lined tubing can provide in applicable downhole environments, such as injection, disposal, and production.

Bare Steel / IPC Standard vs Thermoplastic Lined Pipe (TPL)
Metric Bare Steel / IPC Standard WFES Lined Tubing Operational Impact
MetricAbsolute Surface Roughness Bare Steel / IPC35 microns (0.00138 inches) WFES Lined1.5 microns (0.00006 inches) Operational ImpactLined is 23x smoother, reducing friction and turbulence.
MetricCoefficient of Friction (COF) Bare Steel / IPC0.20 to 0.30 WFES Lined~0.12 (35% to 45% reduction) Operational ImpactSignificantly reduces rod load and increases fatigue life.
MetricHazen-Williams C-Factor (Fluid Flow) Bare Steel / IPC100 / 150 WFES Lined160 Operational ImpactHigher smoothness compensates for ID restrictions.
MetricAsset Recovery Rate Bare Steel / IPC40% to 50% (50-60% scrap rate) WFES Lined80% to 90% Operational ImpactSaves approximately $100,000 per pull in a 10,000-ft well.
MetricReliability (Injection/Disposal) Bare Steel / IPCCommon repetitive failures WFES LinedZero recorded holes since 1992 Operational ImpactLargely mitigates HIT failure, the most common cause of workovers.
MetricWireline Speed Restrictions Bare Steel / IPCNACE-mandated 100 ft/min limit WFES LinedVirtually unlimited wireline speed Operational ImpactEnables quicker, safer, and lower-cost wireline interventions.
MetricChemical limitations Bare Steel / IPCRequires chemical inhibition WFES LinedChemically inert liner material selected for the service environment Operational ImpactAllows operators to reduce or eliminate chemical spend on corrosive inhibitors.
MetricInternal Diameter (ID) Bare Steel / IPCNominal (e.g., 2.441" for 2-7/8") WFES LinedReduced by ~0.30" (6-9 mm) Operational ImpactSmoothness maintains flow capacity despite lower ID.
MetricPumping Efficiency Bare Steel / IPCBaseline WFES LinedUp to 17% power reduction Operational ImpactLower friction allows system to move unrestricted.
MetricMechanical Resilience Bare Steel / IPCBrittle; prone to impact damage WFES LinedDuctile; resists handling damage Operational ImpactFlexible liner creates an "elastic buffer" against rod wear.

// Reducing costs, extending capital asset utility, & protecting revenue

Lining Used
Pipe

With used pipe lining services, Western Falcon helps you recover more value from the assets you already own.

The cheapest tubing decision is not always the lowest upfront purchase. In production, injection, and disposal wells, the real cost of a tubing string is measured over every pull, inspection, replacement, workover, conversion, and reinstallation. When pipe is pulled from service, operators are often forced to choose between scrapping usable steel, burning out damaged IPC, or purchasing new coated tubing for related runs.

WFES used pipe lining gives operators another path. Where tubing condition allows, existing pipe can be inspected, prepared, lined, and returned to service, including pipe with existing or damaged IPC. This helps preserve the steel asset, reduce unnecessary scrap, eliminate ESG risk from thermal burnout, and greatly reduce the total cost of ownership across multiple service cycles.

For operators managing large tubing inventories, late-life conversions, injection programs, disposal wells, or repeat failure environments, lining can revitalize the economics of the entire field.

// Designed and deployed by technical experts

Licensee Partnerships

To bring thermoplastic liner technologies closer to the fields they serve, Western Falcon Energy Services equips technical service companies worldwide to acquire, install, and service patented liners within their regional basins. Through facility design and ongoing support, we ensure our high standards of quality and liner longevity are upheld even in remote downhole environments.

With a flagship facility in Duqm, Oman, WFES has partnered with United Special Technical Services (USTS) to provide end‑to‑end thermoplastic liner solutions for Middle East oil and gas operations. With solutions ranging from reservoirs to processing facilities, operators can select technologies, connections, and recovery methods that match their unique operating needs.

// Streamlining your operations

Vertically-Integrated
Tubing Technology

One technical partner. End-to-end capabilities. Fewer compromises from mill to install.

WF Steel

Tighter specifications start with better steel. WF Steel gives operators access to IS+ domestic ERW, Arvedi SRM as a seamless alternative, and custom-engineered tubulars matched to the chemistry of your well.

From the first call to installation, WFES brings steel, processing, liners, and connections into one coordinated lifecycle package. WFES is your single point of contact and technical partner, ensuring downhole performance guides every design and manufacturing decision.